Furnace Maintenance, Service Policies

Free Estimates on Installations

Air Conditioner & Furnace Service / Maintenance You Can Trust

Don't get caught in the cold or heat. Bill's Refrigeration & Air Conditioning, Inc. recommends that you have system checked out before the heat of the summer or the bone chilling cold of the winter.

Maintenance Service

Our summer checkups include the cleaning of the outdoor coil and the evaporator drain lines as well as checking safeties, refrigerant levels, and electrical components. For winter checkups, we service and clean the burner assemblies, make sure the controls are working, and oil the motors where necessary. Both checkups include a diagnostic check of the equipment and a 15-point seasonal check. We advise you of any parts that are no longer operational or that look like they could fail during the summer / winter season. We carry most parts on the truck, so we can replace nearly anything that you approve in a timely manner.

Routine Maintenance Service Policies

Our Peak Performance service policies are a great investment to prevent a system breakdown at the worst possible time. For a fixed price, we come out once in the spring and again in the fall to clean, check and assess the operation of your system. We will make sure everything is operating properly and efficently as possible. If you need to have any parts replaced at the time of service you will receive a 10% discount on those parts. This is a yearly renewable policy.

Repair Work
Call us when your air conditioner or heating system breaks down. We can fix virtually anything and get your system back up and running. We carry most parts on the truck, so we can typically replace any bad part we come across on a repair call. While attending to your call, we do a diagnostic check of the equipment and advise you of any parts that appear to be nearing the end of their functional life. You can decide whether to have us replace them on the current visit or to wait.

Service Checklists

Bill's Refrigeration & Air Conditioning, Inc. provides service for gas furnaces, oil furnaces, air conditioners/heat pumps, and boilers. Please see our checklists below for each of these types of services.

Gas Furnace Service
• Inspect and test thermostat operation.
• Check all safety controls.
• Clean burner assembly.
• Inspect air filter.
• Check pressure switch.
• Check inducer draft motor.
• Set exposed dampers to heating positions (no balancing).
• Inspect humidifier (if equipped).
• Lubricate any moving parts (if required).
• Check belt(s) and adjust tension (if equipped).
• Check temperature rise.
• Check gas valve operation.
• Inspect pilots, thermocouples (as equipped).
• Clean flame sensor.
• Inspect wiring and connections.
• Inspect blower motor and assembly.

Air Conditioner/Heat Pump Service
• Inspect and test thermostat operation.
• Install gauges and check operating pressures.
• Check refrigerate charge.
• Check voltage and amperage draws.
• Measure air temperature split.
• Check for refrigerant leaks in accessible areas.
• Lubricate any moving parts (if required).
• Check belt(s) and adjust tension (if equipped).
• Inspect filter.
• Check pressure switches.
• Check contactor contacts for pitting or damage.
• Check condensate drain.
• Clean condensate pump (if equipped).
• Inspect wiring and connections.
• Check electrical lock out circuits.

Oil Furnace Service
• Inspect and test thermostat operation.
• Clean and adjust all safety controls.
• Clean burner assembly.
• Set exposed dampers to heating positions (no balancing).
• Inspect humidifier (if equipped).
• Lubricate any moving parts (if required).
• Check belt(s) and adjust tension (if equipped).
• Check temperature rise.
• Change burner nozzle.
• Change oil filter.
• Inspect wiring and connections.
• Check draft.
• Inspect blower motor and assembly.

Boiler Service
• Inspect and test thermostat operation.
• Inspect water feeder, pressure reducer, and fill valve.
• Inspect air scoop.
• Check high and low limit controls.
• Inspect pressure and temperature relief valve.
• Inspect temperature / pressure gauges.
• Inspect air bleeders and purge valves.
• Inspect zone valves.
• Inspect aquastat control.
• Inspect backflow preventer.
• Inspect expansion tank.
• Inspect operation of circulators motors.
• Inspect and check operation of controls and switches.
• Lubricate any motors (if required).
• Inspect for leaks and signs of corrosion.
• Inspect barometric damper.
• Check low water cutoff.
• Clean burner assembly.
• Inspect pilot assembly (if equipped).